Products
Interceptor
Analogic
Aeroscan
Sensors


SEMA Member

The sensor kits listed below are OEM quality units with 0-5v outputs which are compatible with our gauges. For those who already have an Aeroforce gauge these provide an inexpensive and easier alternative to buying and installing separate gauges for these functions.

Sens029 Ethanol Content and Fuel Temperature Sensor Kit uses a sophisticated sensor that measures both ethanol % and fuel temperature. The sensor connects to a small control unit that outputs two 0-5v signals proportional to ethanol % and fuel temperature. These signals can be connected to our Interceptor or Analogic gauge, or to any data logging device that accepts a 0-5v signal.

$245.00
learn more about this kit


Sens030 Ethanol Content and Fuel Temperature Controller Kit contains everything included in the full Sens029 kit minus the sensor itself. A GM P/N 13577429 sensor or GM P/N 13577379 sensor are required. NOT INCLUDED The small control unit outputs two 0-5v signals proportional to ethanol % and fuel temperature. These signals can be connected to our Interceptor or Analogic gauge, or to any data logging device that accepts a 0-5v signal.

$165.00
learn more about this kit


Wide band O2 sensor kit for Air/Fuel ratio:
Each kit consists of a sensor, controller, steel bung, and cabling allowing you to connect directly to the Interceptor gauge. These accurate sensors use the new Bosch LSU4.9 sensor and are available at a very affordable price.

$189.00
learn more about this kit


Oil/Fuel and General Pressure Sensors:
Each kit consists of a sensor and connector/pigtail. These accurate sensors have NPT fittings, 0-5v outputs, and of course are compatible with our gauge products.

$65.00 
learn more about this kit

Boost/Vacuum sensor kits:
Each kit consists of a sensor and connector/pigtail. These accurate sensors are rated at 2 bar, 3.5 bar, and 7 bar (not shown).

$50.00 - $98.00 
learn more about this kit

5v regulated power supply
Simply connects to switched 12v and ground to supply 5v to our 2 bar MAP sensor kit. Eliminates the need to tap into other sensor lines or the PCM to obtain 5v.

$23.00 

learn more about this kit

Pyrometer (EGT) kits:

Thermocouple Amplifier/Linearizer
converts EGT probe output to a linear 0-5v signal for use with our gauges or other data logging equipment.

$99.97 
learn more about this kit



EGT probe.
Type K thermocouple with 6' cable, 1/8" NPT fitting. Clamp on style also available.

$64.99 
learn more about this kit

Temperature sensor kits:
Each kit consists of a sensor, signal conditioner, and connector/pigtail allowing you to connect directly to the Interceptor gauge. These accurate sensors are OEM units and are available for use for fluid or air temperature.

$44.95 
learn more about this kit

1900 psi nitrous pressure sensor with 5' pigtail
The nitrous sensor listed below are high accuracy units with 0.5 to 4.5v output which is compatible with our gauges. For those who already have an Aeroforce gauge these provide an inexepensive and easier alternative to buying and installing separate gauges for these functions. Sensor requires 5v power, our 5v regulator is recommended but not required. Sensor has a 1/8" NPT fitting. Click here for installation instructions.

$79 
learn more about this kit

Add-A-Circuit (Pico 10A Mini fuse holder)
This handy device allows you to make one fused circuit into two. This allows you to connect power to our devices without cutting or splicing any wires, thus resulting in an easier and cleaner installation! Simply choose an existing 10A or lower circuit in your fuse block, remove the fuse, insert the add-a-circuit with existing and new fuse, and you have a new fused 12v circuit!

$7.50 

For questions visit our forums here and go to the "Sensor Kit" subforum.

YOU ARE BROWSING: HOME | PRODUCTS | SENSORS© 2005-2009 Aeroforce Technology Inc. All rights reserved.     MADE IN THE USA
SITE BY: MediaBrand

twitter FaceBook youtube